FYCS-Z Fil ak kab Bunched Ekipman tès boule (Mass Flow Controller)

Li se apwopriye pou evalye kapasite nan enstalasyon vètikal nan fourni fil ak kab oswa kab optik siprime flanm dife vètikal gaye nan kondisyon espesifye.

Konfòme ak GB18380.31-2022 "Tès konbisyon nan câbles anba kondisyon flanm dife Pati 3: enstalasyon vètikal nan fil bunched ak kab flanm dife vètikal gaye tès aparèy tès", ekivalan a IEC60332-3-10:2000.

An menm tan an satisfè kondisyon ki nan Tablo 4 nan GB / T19666-2019 "Pwensip Jeneral nan Ignifuge flanm dife ak Refractory Fil ak Kab" estanda.

GB/T18380.32--2022/IEC60332--3--21: 2015 "Tès konbisyon nan câbles elektrik ak câbles optik anba kondisyon flanm dife Pati 32: vètikal enstale fil fil ak kab flanm dife vètikal gaye tès AF / R kategori".

GB/T18380.33--2022/IEC60332--3--22: 2015 "Tès konbisyon nan câbles elektrik ak câbles optik anba kondisyon flanm dife Pati 33: vètikal enstale fil fil ak kab flanm dife vètikal gaye tès kategori A".

GB/T18380.35--2022/IEC60332--3--24:2015 "Tès konbisyon nan câbles elektrik ak câbles optik anba kondisyon flanm dife Pati 35: Vètikal enstale fil fil ak kab flanm dife vètikal gaye tès kategori C",

GB/T18380.36--2022/IEC60332--3--25: 2015 "Tès konbisyon nan câbles elektrik ak câbles optik anba kondisyon flanm dife Pati 36: Vètikal enstale fil fourni ak kab flanm dife vètikal gaye tès kategori D".

Chanm tès konbisyon, sistèm kontwòl elektrik, sous lè, sous ignisyon sistèm kontwòl koule mas (gaz pwopan ak lè konprese gaz), nechèl asye, aparèy pou etenn dife, aparèy pou pirifye emisyon, elatriye.

1.Working voltage: AC 220V±10% 50Hz,Power consumption: 2KW

2.The inlet and outlet air flow rate: 5000±200 L/min(adjustable)

3.Koulman lè a ak koule pwopan yo kontwole pa sistèm kontwòl koule mas.

4.Air sous: pwopan (0.1Mpa), lè (0.1Mpa), sous lè kliyan posede.

5. Timing ranje: 0 ~ 60min (ka mete)

6.Anemometer measurement range: 0 ~ 30m/s, measurement accuracy: ±0.2m/s

7.Test chanm dimansyon (mm): 2184 (L) x 1156 (W) x 5213 (H)

Ranpli ak mineral dife ki reziste materyèl izolasyon wòch lenn mouton, tèt ak 1500mm gwo pwoteksyon sekirite.

8.2 combustion tèt blowtorch ak mixer Venturi

9.Vatik inlet lè a se yon fanatik toubiyon ki ba-bri. PLC a kontwole vitès fanatik la atravè konvètisè frekans lan, ak debimètr vortex la mezire volim lè a pou reyalize kontwòl volim inlet lè egzak.

10. Fanatik bouyon an pwovoke adopte 4-72 fanatik anti-korozyon ak yon volim lè 5000m²/h.

11.Flue gaz apre tretman ekipe ak yon gwo kay won pou retire pousyè espre dlo ak yon volim lè pwosesis 5000 m.²/h

12.Tou de metòd pou etenn dife nitwojèn ak dlo espre dife metòd yo ekipe pou kliyan yo chwazi.

13.Pou tès:

Vètikal estanda asye nechèl dimansyon (mm): 500 (W) x 3500 (H)

Vètikal lajè nechèl dimansyon (mm): 800 (W) x 3500 (H)

14.Combustion sifas dimansyon (mm): 257 (L) x 4.5 (W)

15.Touch ekran kontwòl, entwisyon ak klè, ignisyon elektwonik, distribisyon otomatik.

16.Se brûler la kontwole pa PLC ak opere pa manyen ekran.

Test box: The experimental device should be a self-standing box with a width of 1000mm, a depth of 2000mm and a height of 4000mm. The bottom of the box should be 300mm above the ground. The perimeter of the test chamber should be sealed, the air from the bottom of the chamber from the front wall (150±10) mm to open a (800±20) mm x (400±10) mm air inlet into the box. A (300±30) mm x (1000±100) mm outlet should be opened at the back of the top of the chamber. Test chamber should be used on both sides of the heat transfer coefficient of about 0.7W.m-2.K-1 thermal insulation, the distance between the steel ladder and the back wall of the test chamber is (150±10) mm, and the bottom rung of the steel ladder is (400±5) mm from the ground. The lowest point of the cable sample is about 100mm from the ground.

• 

   Estanda Venturi Blowtorch

• 

   Blowtorch twou

• 

  Brûler 

• 

  Venturi mixer

1.Anemometer: mezire vitès van an deyò tèt la nan chanm tès la, si vitès van an depase 8m / s Lè sa a, tès la pa ka fèt.

2.Tanperati pwofonde: de K-kalite tèrmokapteur yo ekipe sou tou de bò bwat tès la, si tanperati a nan miray enteryè a pi ba pase 5 ℃ oswa pi wo pase 40 ℃, tès la pa ka fèt.

3.Air source: adopt touch screen controller, frequency conversion control inlet axial flow fan, can intuitively read out and control the gas flow through the air box for (5000±200) L/min, stable air flow rate during the test.

4.Apre tès la fini: Si echantiyon an toujou ap boule apre yon èdtan nan sispann dife a, yo ka itilize yon aparèy espre dlo oswa aparèy pou etenn dife azòt pou fòse sispann dife a, epi gen yon antonwa espesyal pou netwaye. fatra.

5.Steel ladder type: width (500±5)mm standard steel ladder, width (800±10)mm wide steel ladder, material for SUS304 stainless steel tube.

Youn chak pou nechèl asye estanda ak lajè

Koleksyon lafimen ak aparèy swi lave: materyèl PP, ak yon dyamèt 1500mm ak yon wotè 3500mm. Se gwo kay won an koleksyon lafimen divize an twa pati: aparèy espre, lafimen ak aparèy filtre pousyè, ak aparèy echapman lafimen. Aparèy espre: bay espre dlo pou materyèl filtre espesyal, kenbe materyèl filtre espesyal yo filtre lafimen ak pousyè tè efektivman. Lafimen ak pousyè filtre aparèy: Filtre pa materyèl filtre dlo pou bwè, ki ka efektivman filtre lafimen ak pousyè tè pou ke lafimen ki emèt la se lafimen blan. Kliyan ajoute ekipman pwoteksyon anviwònman selon sitiyasyon an.

• 

  Smoke Collection Tower Schematic

• 

  Gwo kay won koleksyon lafimen

• 

  Fanatik bouyon pwovoke

1.Ignition source type: including one or two band-type propane gas blowtorches and their matching flowmeters and Venturi mixers. The ignition surface is drilled with 242 flat metal plates with a diameter of 1.32mm. The center distance of these holes is 3.2mm, arranged in three rows in a staggered arrangement, each row is 81, 80 and 81, distributed in the nominal size is 257×4.5mm. In addition, a row of small holes are opened on both sides of the flame board, and this guide hole can maintain the stable combustion of the flame.

2.Ignition source location: The torch should be placed horizontally, (75±5) mm from the front surface of the cable sample, (600±5) mm from the bottom of the test chamber, and symmetrical to the axis of the steel ladder. The flame supply point of the blowtorch should be located in the center between the two crossbeams of the steel ladder, and at least 500mm away from the lower end of the sample. The center line of the blowtorch system should be approximately the same as the center line of the steel ladder.

• 

  Vortex Flow Meter pou
  Kontwòl egzak nan Inlet Air Volim

• 

  Vortex lè inlet fanatik

Kontwolè mas koule a itilize pou mezi egzak ak kontwòl mas koule gaz la. Mèt koule mas gen karakteristik segondè presizyon, bon repetibilite, repons rapid, kòmanse mou, estabilite ak disponiblite, lajè ranje presyon opere. Avèk konektè estanda entènasyonal yo, li fasil pou opere ak itilize, yo ka enstale nan nenpòt pozisyon, epi fasil pou konekte avèk yon òdinatè pou kontwòl otomatik.

Paramèt teknik kontwolè mas koule:

1.Accuracy: ±2% F.S

2.Linearity：±1% F.S

3.Repeat accuracy：±0.2% F.S

4.Response time：1 ~ 4 sec

5.Pressure rezistans: 3 Mpa

6.Working environment：5 ~ 45℃

7.Input modèl: 0-+5v